The Court Blood - Enemy - Ashnar - The Pale Emperor, creatures of darkness, Enemy, Flesh of Gods, for Wargames, Dungeons & Dragons TTRPG
$5.45
Printed in full unhollowed resin.
Good quality resin (40USD/kg).
25mm Base supplied.
Scale 28mm.
Height 43mm
In the realm of Dungeons and Dragons, where magic and mystery abound, there exists a dark and sinister place known as The Court of Blood. This is not a realm of noble kings and virtuous knights, but rather a twisted and malevolent domain ruled by creatures of darkness and shadow. From the depths of the darkest forests to the heart of the foulest swamps, The Court of Blood is a place of fear and dread, where the very air is thick with the stench of death and decay.
The denizens of The Court of Blood are not your typical inhabitants of the realms of Dungeons and Dragons. They are creatures of nightmare and legend, twisted and corrupted by dark and malevolent forces. From savage werewolves and bloodthirsty vampires to cunning witches and malevolent demons, they are the stuff of nightmares, feared and reviled by all who dwell in the world of mortals.
But The Court of Blood is not just a place of darkness and despair – it is also a place of power and intrigue. At his heart lies the Blood Throne, where the rulers of The Court hold sway over their twisted domain. From this dark and foreboding fortress, they plot and scheme, weaving webs of deceit and treachery to further their own dark agendas. It is said that those who sit upon the Blood Throne wield power beyond imagining, their wills bending reality itself to their whims.
Yet despite the darkness that permeates The Court of Blood, there are those who dare to defy its rulers and challenge its authority. These are the rebels and outcasts, the brave souls who refuse to bow before the forces of darkness and who fight for freedom and justice against all odds. Armed with swords and spells, they venture into the heart of The Court, facing untold dangers and horrors as they strive to overthrow the tyrants who rule over them.
But The Court of Blood is not a place where heroes thrive. It is a place of darkness and despair, where hope is but a fleeting dream and death lurks around every corner. Those who dare to enter its twisted halls do so at their own peril, risking life and limb in pursuit of glory and redemption. Yet for some, the lure of power and the promise of adventure are too great to resist, and they willingly throw themselves into the fray, knowing full well the dangers that await them.
In the world of tabletop gaming, Proxy Wars offers players the chance to explore the dark and twisted realm of The Court of Blood with finely crafted resin figurines that capture the essence of its malevolent inhabitants. Each miniature masterpiece is meticulously designed and 3D printed, allowing players to immerse themselves in the dark and foreboding atmosphere of Dungeons and Dragons.
Shipping from Portugal
Processing time
1-4 business days
Estimated shipping times
- France : 7 - 10 business days
- North America : 12 - 20 business days
I'll do my best to meet these shipping estimates, but can't guarantee them. Actual delivery time will depend on the shipping method you choose.
Customs and import taxes
Buyers are responsible for any customs and import taxes that may apply. I'm not responsible for delays due to customs.
Payment Options
Returns & Exchanges
I gladly accept returns and exchanges
Just contact me within: 14 days of delivery
Ship items back to me within: 30 days of delivery
I don't accept cancellations
But please contact me if you have any problems with your order.
Conditions of return
Buyers are responsible for return shipping costs. If the item is not returned in its original condition, the buyer is responsible for any loss in value.
Frequently Asked Questions
Return policy?
We apply, the satisfied or refunded. So we do not accept returns. If there is a problem with the order we will resend or refund you, it's easier.
Production time?
In general, articles are produced in series to have stock available and to send orders within 2 to 3 days. However, some items with less sales may take 1 week. It is therefore better to allow one week on average for shipping. Do not hesitate to contact us if your order is urgent, for example for a work commission.
Lost packages?
It sometimes happens that the package is lost, damaged or amputated by the carrier. In these cases we will offer you either a reshipment or a refund.
PLA or Resin?
We mostly use SUNLU PLA+, and good quality resin (arround 50$/L). The FDM printed PLA is printed at 0.2mm / layer (usually 0.1 for high quality) and is cheaper than Resin (0.05mm/layer). We strongly advise you to choose Resin printed article to get the best quality on small details. But in most case PLA gives a good enough tabletop experience.
Resin miniatures quality?
The evolution of technology has made possible to have a quality that is far superior to failcasting, although still inferior to last generation plastic injection.
The miniatures that we print are full to avoid all the problems that could cause non-solidified resin inside.
We try to harden the miniatures enough but not too hard to keep them easy to rework / customize. We remove the vast majority of supports, but a small part may remain, especially on small, very thin parts.
Our pricing policy does not allow us to have perfect quality control, so we prefer to add a little content to compensate in case of problem on a miniature. However do not hesitate to contact us in case, we will resend the damaged miniatures as soon as possible.
Resin miniatures treatment?
Once you have received your figurines run them in hot water and trim them before exposing them to the sun for a few minutes. Usually these steps are optional but they only take a few minutes. If some parts are slightly bent, run them in hot water and you can straighten them easily.
Then make sure you have a very strong glue to assemble them, or use milliput/greenstuff in addition at the intersections. The best glue is GW's. Unlike plastic, the parts must be tightened very hard for at least 20 seconds. The best method is to use a thin layer of greenstuff at the intersections; the green stuff sticks well to the resin and sticks well so it solves the problem.
Customization?
We're happy to consider customization requests, and some of our products are designed with customization in mind. However, due to time constraints, we're unable to take on modeling requests for strictly personal projects at the moment.
Team and synergy?
As the project grows, the team widens and specializes. Everyone remains very free and brings their specific know-how. We would prefer to share the profits if we can provide you with better service in return. And we still have a lot of projects in the pipeline, which will require new skills.
Current collaborations?
At the moment, we're collaborating with several YouTubers from France who generously provide us with feedback and expose us to their audience. In the upcoming months, we're planning to expand our services to other wargame channels that speak English. Specifically, our game accessories can significantly improve the readability of online battle reports. Moreover, we aim to collaborate with other 3D modeling artists. If you possess the necessary skills and are interested in contributing to the growth of the Damocles world, or if you're considering starting a YouTube channel and would like a free set to begin with, please don't hesitate to contact us.